View 14H26-SZ3M-400-0LC_4585713.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3MTM Mini D Ribbon (MDR) Cable Assembly
.050" High Speed Digital CameraLinkTM Cable - Right Angle 14H26-SZ3X-XXX-0LC
* Supports Industrial CameraLinkTM standard for camera to frame grabber communications * Space-saving right angle cable exit * 11 shielded twin-ax pairs and four drain wires * Entire cable bundle is shielded with foil and braid for additional signal protection * Rugged MDR ribbon type contact * Rugged thumbscrew retention * EMI shielded junction shell on straight end * EMI shielded overmolded shell on right-angle end * See Regulatory Information Appendix (RIA) for chemical compliance information
Date Modified: January 24, 2008 TS-2262-A Sheet 1 of 3
Physical
Connector Contact Plating Wiping Area: 30 " [0.76 m] Min. Gold (RIA E1 & C1 apply) Overmolded Shell: Color: Black Material: Polyvinyl Chloride (PVC) Shell: Color: Beige Material: Polyester Elastomer Cable: Color: Beige Jacket Material: Polyvinyl Chloride (PVC) Flammability: AWM VW-1
Electrical
Voltage Rating: 30V Current Rating: 1 A Insulation Resistance: > 1 x 108 at 100 VDC Withstanding Voltage: 350 VRMS for 1 minute Individually Shielded Twisted Pairs Characteristic Impedance: 100 10 Conductor Size: 28 AWG Stranded Propagation Velocity: 1.25 ns/ft [4.1 ns/m ] Skew (within pair): 50 ps/meter maximum Skew (channel skew per chipset): 50 ps/meter maximum
Environmental
Temperature Rating: -20 C to +75 C
UL File No.: E86982 3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
3MTM Mini D Ribbon (MDR) Cable Assembly
.050" High Speed Digital CameraLinkTM Cable - Right Angle
Right-Angle End
14H26-SZ3X-XXX-0LC
Straight End
39.7 [1.56] 19.4 [0.76]
#4-40 Thumbscrews
39.7 [1.56]
2X 26 Position High Density Mini D Ribbon (MDR) Male Plug
12.8 [0.51] Cable Length 42.4 [1.67] 32.5 [1.28]
Cable Length Tolerance is the Larger of +50mm / -0mm or +3% / -0%
MDR 26 Position Plug Right-Angle End
MDR 26 Position Plug Straight End 1 13
14
26
mm [inch] Tolerance Unless Noted
14H26-SZ3M-XXX-0LC
14H26-SZ3S-XXX-0LC
mm
Use 3MTM Jacksocket 3341-31 for mounting receptacle to panel.
[ ] Dimensions for Reference Only
.0 .1
.00 .10
Ordering Information
14H26-SZ3X-XXX-0LC
Right Angle Orientation M = Position 1 opposite cable S = Position 1 on cable side 050 100 150 200 250 = = = = = 50 cm 100 cm 150 cm 200 cm 250 cm
Cable Length
300 350 400 450 500 = = = = = 300 cm 350 cm 400 cm 450 cm 500 cm 600 700 800 900 A00 = = = = = 600 cm 700 cm 800 cm 900 cm 1000 cm
For lengths greater than 1000 cm refer to Table 2
TS-2262-A Sheet 2 of 3
3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/
3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
3MTM Mini D Ribbon (MDR) Cable Assembly
.050" High Speed Digital CameraLinkTM Cable - Right Angle
Table 1. Cable Assembly and Camera Link Pinouts Medium and Full Configurations Two Channel Link Chips Camera Connector 1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 13 23 11 24 12 15 13 26 Right Angle Frame Grabber 1 14 25 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 13 26 Channel Link Signal inner shield inner shield Y0Y0+ Y1Y1+ Y2Y2+ YclkYclk+ Y3Y3+ 100 ohm terminated Z0Z0+ Z1Z1+ Z2Z2+ ZclkZclk+ Z3Z3+ inner shield inner shield Cable Name (Reference only) inner shield inner shield Pair 1 Pair 1 Pair 2Pair 2+ Pair 3Pair 3+ Pair 4Pair 4+ Pair 5Pair 5+ Pair 6+ Pair 6Pair 7Pair 7+ Pair 8Pair 8+ Pair 9Pair 9+ Pair 10Pair 10+ Pair 11Pair 11+ inner shield inner shield Base Configuration One Channel Link Chip + Camera Control + Serial Communication Camera Connector 1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 13 23 11 24 12 15 13 26 Table 2 Length Codes First 2 Digits 10 11 12 13 14 15 16 Alpha Code A B C D E F G First 2 Digits 17 18 19 20 21 22 23 Alpha Code H J K L M N P First 2 Digits 24 25 26 27 28 29 30 Alpha Code R S T V W Y Z Right Angle Frame Grabber 1 14 25 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 13 26 Channel Link Signal inner shield inner shield X0X0+ X1X1+ X2X2+ XclkXclk+ X3X3+ SerTC+ SerTCSerTFGSerTFG+ CC1CC1+ CC2+ CC2CC3CC3+ CC4+ CC4inner shield inner shield
14H26-SZ3X-XXX-0LC
Notes: 1. All pairs are individually shielded with aluminum foil. 2. Pair shields are wrapped aluminum out and are in contact with four internal drains (logic ground). 3. Outer braid and foil (chassis ground) are isolated from inner drains (logic ground). 4. Cable assembly compatible with both CameraLink configurations.
For lengths in excess of 1000 cm substitute the corresponding alpha code for the first 2 digits. Example: the code for 1160 cm is B60.
TS-2262-A Sheet 3 of 3
3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/
3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/717/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
CHINA Appendix C1: China RoHS
Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below.
RIA-2217B-D
Appendix C3: China RoHS
Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below.
Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
3M Electronics Solutions Division
6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. (c) 3M 2008. All rights reserved. RIA-2217B-D
3M is a trademark of 3M Company.

▲Up To Search▲

Price & Availability of 14H26-SZ3M-400-0LC

	To Download 14H26-SZ3M-400-0LC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .